Canoga-perkins 9145E NID Software Version 4.10 Manuel d'utilisateur Page 219
- Page / 296
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Service OAM 9145E NID Software User’s Manual
SOAM Configuration
207
Figure 11-7 SOAM Configuration screen
NOTE: You can perform system-level configuration before or after you configure Maintenance
Domains or other entities.
4. On the SOAM System Level Configuration screen (Figure 11-8), type 1 and press Enter.
5. Press the Space bar to select Enabled or Disabled and press Enter. If Service OAM
procedures are disabled for the system, no Service OAM packets are captured and
processed. Instead, all Service OAM packets received by the 9145E NID are
transparently forwarded, using the same rules as for data plane traffic.
6. When you are prompted to change SOAM status, type Y and press Enter to save the
setting, or type N to return to the original setting.
7. To select a Chassis ID Format, type 2 and press Enter. Select one of the following
settings:
• MAC Address, and press Enter. The Chassis ID value is read only. You cannot
change the value on this screen.
• Network Address, and press Enter. The Network Address value is read only. You
cannot change the value on this screen.
• Locally Assigned, and press Enter. This selection allows you to enter a custom
string.
Canoga Perkins Corp. Ethernet Network Interface Device 02-JAN-2009
9145E-101-1-0 V04.10 05:15:27
------------------------------SOAM CONFIGURATION-------------------------------
1) System level configuration
2) Maintenance Domains (MDs)
3) Maintenance Associations (MAs)
4) Maintenance Entity Groups (MEGs)
5) Maintenance End Points (MEPs)
6) Maintenance Intermediate Points (MIPs)
7) Configuration Error List
Select [1-7]:
------------------------------------Messages-----------------------------------
- 9145E NID Software 1
- Version 4.10 1
- User Manual 1
- About this Manual 3
- How this Manual is Organized 3
- New in this Revision 4
- Contacting Technical Support 4
- Document Feedback 4
- Contents 5
- Chapter 1 13
- Introduction 13
- 1.3 Three Levels of Security 14
- Chapter 2 15
- Getting Started 15
- 2.1.1 About MIBs 16
- 2.1.2 9145E Set-up 16
- 2.3 Login 17
- 2.4 Main Menu 18
- Main Menu 19
- 2.5 Supported MIBs 20
- Chapter 3 21
- System Configuration 21
- System Configuration Menu 22
- IP/SNMP Agent Configuration 24
- 3.2.3 Host Table 29
- 3.2.4 Trap Table 31
- 3.3 Trap Configuration 36
- 3.4 Security Configuration 38
- Security Configuration 39
- 3.5 Account Configuration 41
- 3.5.2 Add or Edit an Account 42
- Account Configuration 43
- 3.5.3 Delete an Account 44
- 3.6 System Information 45
- 3.7 RADIUS Client 46
- RADIUS Client 47
- SNTP Client Configuration 48
- SYSLOG Client Configuration 50
- 3.10 Hardware Information 51
- Hardware Information 52
- Chapter 4 53
- Diagnostics 53
- 4.2 Latency/Jitter Test 54
- Latency/Jitter Test 55
- 4.3 PING Generation 57
- PING Generation 58
- 4.4 VLAN Loopback 59
- Figure 4-6 VLAN Loopback 60
- VLAN Loopback 61
- 4.4.2 L2 Ping Generation 62
- 4.5 Cable Diagnostics 63
- Cable Diagnostics 64
- 4.6 Network Performance 65
- 4.6.1.1 Round-Trip Latency 67
- 4.6.1.2 One-Way Jitter 67
- 4.6.2 Profiles 69
- 4.6.2.1 Setting up a profile 70
- 4.6.3 Test Addresses 77
- 4.6.5 Trap Configuration 82
- 4.6.6 Statistics 83
- 4.6.7 PM Scheduler 84
- 4.6.8 PM Test Results 85
- 4.6.9 PM Manual Test 89
- 4.6.11 SAM Test Results 93
- 4.6.12 SAM Scheduler 95
- 4.6.13 SAM Results Log 96
- 4.6.15.1 PLPM Configuration 99
- Network Performance 100
- 4.6.15.3 How PLPM Works 101
- 4.6.15.5 Configuring PLMP 108
- 4.7 Throughput Testing 110
- 4.7.1 Test Setup 111
- Throughput Testing 112
- 4.8 SOAM Based Diagnostics 113
- SOAM Based Diagnostics 114
- Service Activation Testing 117
- 4.9.4 L2CP Profiles 137
- Chapter 5 141
- Port Information 141
- 5.1 Link Status 142
- 5.2 Port Configuration 143
- 5.2.1 Hardware Information 144
- Port Configuration 145
- 5.2.3 VLAN Configuration 147
- 5.2.3.4 C-VLAN/PCP Policers 152
- 5.2.4 Port Filters 154
- 5.2.4.4 Setting Port Filters 156
- 5.2.4.5 L2CP Port Filters 158
- 5.2.6 Port Level Policers 161
- 5.3 Layer 2 Statistics 163
- Layer 2 Statistics 164
- 5.4 RMON Group 1 Statistics 167
- RMON Group 1 Statistics 168
- Chapter 6 169
- System Alarms & Logs 169
- 6.1 System Log 170
- System Log 171
- Chapter 7 173
- Utilities 173
- 7.3 Change Password 174
- 7.4 VT100 Baud Rate 174
- 7.5 PING Generation 175
- 7.6 Static ARP Table 175
- 7.7 Dynamic ARP Table 176
- 7.8 License Manager 177
- License Manager 178
- Chapter 8 179
- Software Upgrade 179
- 8.5 Hardware Reset 182
- Chapter 9 185
- Link OAM 185
- 9.1 OAM Control 186
- 9.1.2 OAM Max PDU Size 187
- 9.1.3 OAM Revision 187
- 9.1.4 OAM Functions 187
- 9.1.5 OAM Loopback Status 187
- 9.1.6 OAM Remote Fault 187
- OAM Control 188
- 9.2 OAM Peer Information 189
- 9.3 OAM Statistics 190
- 9.4 OAM Event Configuration 191
- 9.5 OAM Event Log 192
- OAM Event Log 193
- Chapter 10 195
- CoS Configuration 195
- 10.2 CoS Support 196
- 10.3 Classifier Mapping 197
- 10.3.2.1 IP Precedence Mode 198
- 10.3.2.2 DSCP Mode 199
- 10.3.2.3 AF/EF Mode 200
- 10.4 Queue Configuration 201
- Queue Configuration 202
- 10.4.3 Scheduling Scheme 204
- 10.4.4 Weight Parameters 204
- 10.6 Queue Statistics 206
- Queue Statistics 207
- Chapter 11 209
- Service OAM 209
- 11.1.1 SOAM Entities 210
- 11.1.4 SOAM Protocols 213
- 11.1.7 Screen Navigation 216
- 11.2 SOAM Configuration 217
- Figure 11-5 Main Menu 218
- SOAM Configuration 219
- 11.3 Maintenance Domains 221
- Maintenance Domains 222
- Maintenance Associations 225
- Maintenance Entity Groups 229
- 11.6 Maintenance End Points 235
- Maintenance End Points 236
- 11.6.6 Linktrace Procedures 241
- 11.6.7 Loopback Procedures 244
- 11.8.1 MEP Statistics 254
- 11.8.2 MIP Statistics 255
- 11.6.6.2 MEP Statistics 257
- 11.6.6.2 MIP Statistics 257
- 11.7 AIS Configuration 258
- AIS Configuration 259
- Chapter 12 261
- Configuring EVC 261
- 12.1.4 Statistics 262
- 12.1.5 Screen Navigation 263
- EVC Functionality 264
- 12.2 EVC Configuration 265
- 12.2.1 Create an EVC Record 266
- 12.2.2 Delete an EVC Record 267
- 12.2.3 Modify an EVC record 268
- EVC Configuration 269
- S-TPID/T-TPID Configuration 277
- Chapter 13 279
- Bandwidth Profiling 279
- Bandwidth Profiles 280
- 13.2 Policers 281
- 13.3 Shapers 282
- Shapers 283
- 13.3.1 Shaper statistics 284
- 13.6.1 Modifying a Policer 289
- 13.7.2 Modifying a Shaper 292
- 13.8 Clock Rate Granularity 293
- 13.9 Color Marking Method 293
- Color Marking Method 294
- CANOGA PERKINS CORPORATION 296
Produits connexes et manuels pour Matériel informatique Canoga-perkins 9145E NID Software Version 4.10
Matériel informatique Canoga-perkins 9145E Network Interface Device Software Version 2. Manuel d'utilisateur
(112 pages)
(112 pages)
Matériel informatique Canoga-perkins 9145E Standard NID Software Version 1.0 Manuel d'utilisateur
(100 pages)
(100 pages)
Matériel informatique Canoga-perkins 9145E10G Network Interface Device Hardware Manuel d'utilisateur
(55 pages)
(55 pages)
Matériel informatique Canoga-perkins 9145E10G NID Software Version 1.0 Manuel d'utilisateur
(116 pages)
(116 pages)
Matériel informatique Canoga-perkins 9145EMP Network Interface Device Hardware Manuel d'utilisateur
(50 pages)
(50 pages)
Matériel informatique Canoga-perkins 9145EMP NID Software Version 3.1 Manuel d'utilisateur
(202 pages)
(202 pages)
Matériel informatique Canoga-perkins 9145EMP NID Software Version 4.0 Manuel d'utilisateur
(229 pages)
(229 pages)
© 2020, manymanuals.fr. Tous droits réservés | 1.170 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels